DENT PULLING SYSTEMS

 

Save Time, Save Panels, Save Money!

Stanners Dent Expert ULTRA

REF:STA703

The Stanners Dent Expert ULTRA is the latest steel dent pulling unit.

 

This unit offers high power and a fast weld time, with zero burn through on the inside panel which is better for corrosion prevention in the future.

Stanners Alu Arc Gas Pull

REF:STA700

Stanners offers the latest aluminium dent puller in our range.


Unlike traditional capacitor discharge units where threaded studs were welded to the panel, the new system welds an aluminium key to the panel like a traditional steel dent puller.


The unit also uses pure argon gas to shield the welding process and create a cleaner weld to the surface of the aluminium panel.


The result is a quicker process and much stronger weld giving the ability to do larger repairs (within reason) to aluminium panels over traditional older aluminium dent systems.

Stanners Dent Expert Basic Power Source

REF:STA150

The Stanners Dent Expert Unit is a 240v single phase Heavy Duty power unit, ideal for light repair work and works from a 13amp plug.

Kit Contains:

  • Weld on Slide Hammer

  • Accessory Box of Consumables

Available with a 240v or 400v 3ph unit!

Stanners Basic Dent Pulling System

REF:STA/DENT/01

The Stanners Basic Dent Pulling System contains a wide array of tools for the busy bodyshop in a compact portable package for easy manoeuvring around the workshop. This kit is available with either a single or three phase unit.

Kit Contains:

  • Weld on Slide Hammer

  • Accessory Box of Consumables

  • Lever puller with a choice of weld on tip or claw

  • Weld on Handy Puller

  • Air Powered Suction Puller

  • Slider hammer with single or 6 claw hook

  • 0.75m Long Pulling bridge with a choice of 2,4 or 6 hook claw

Heavy duty transformer power source, available in 1or 3 phase.  

Heavy duty pulling accessories for larger repairs on stronger areas of the vehicle.  

Suitable for commercial use.

 

Kit contains:

  • 0.75 pulling bridge with a choice of 2, 4 or 6 hook

  • Lever puller with a choice of weld tip or claw

  • Suction Puller

  • Weld on Slide Hammer

  • Slide Hammer with single or 6 hook claw

  • Weld on Handy Puller

  • Re-inforced 0.75 Pulling bridge with suction pads (fixed &- swivel feet)

  • Re-inforced 1.2 Pulling bridge with suction pads (fixed & swivel- feet)

  • Carbon pencil shrinking tool

  • High spot shrinking tool

  • Weld on key tools & facility

  • Weld on wire tools & facility

  • Weld on threaded studs

  • Accessory Box

  • Consumables & Spares

Stanners Advanced Dent Pulling System

REF:STA/DENT/02

SW15 Aluminium Dent Puller

REF:STA155

The Stanners SW15 Aluminium Dent Pulling unit offers the following features:

  • Repair to dents on Aluminium panels using the latest Captive Discharge Welding

  • Pulling studs welds to the surface of panel, there is no burn through to rear side of panel.

  • No need to remove trims or re-paint rear side of panel.

  • Spring loaded handle allows operator to apply correct pressure each time to weld stud on correctly.

  • By use of handy puller the operator can massage small dents out gently.

  • Stud is removed from panel by either a final hard squeeze or a twist action using a pair of side cutters.

Stanners Combi Unit

The Stanners Combi unit offers the following features-

  • Repair to dents on Aluminium panels using latest Captive Discharge welding
  • Shrink & Re-tension the repair area on Aluminium panels
  • Repair dents on steel panels using Captive Discharge welding (NEW TECHNOLOGY) or by using the normal transformer setting
  • Shrink & Re-tension the repair area on steel panels
  • Pulling stud welds to the surface of panel, there is no burn though to rear side of panel. No need to remove trims or re-paint rear side of panel.
  • Spring-loaded handle allows operator to apply correct pressure each time to weld stud on correctly.
  • By use of handy puller the operator can massage small dents out gently.
  • Stud is removed from panel by either a final hard squeeze of handy puller or a twist action using a pair of side cutters.
  • After removing dents on aluminium, the material needs to be re-tensioned, Stanners offers the only unit on the market that can offer shrinking / re-tensioning tools from a single unit.
  • By use of the copper electrode, you can shrink high points - Other competitors tell you to use gas torch, you have no control to the amount of heat been applied to panel.
  • The technology used to weld the studs is commonly known as captive discharge welding. This works by charging a bank of capacitors to a high DC voltage, and then the charge is released, it will weld the stud to the surface.
  • Full electronics give exact control of this electrical charge; there is a digital display so you can set the required power.
  • A very important feature of this unit is that it will continually charge and discharge the capacitors, meaning that when you press the trigger to weld the stud you get the exact same voltage from stud to stud.
  • One pulling stud welds to all grades of Aluminum panels.

OPENING HOURS

ADDRESS

MONDAY-FRIDAY

8.30AM-5.00PM

​SATURDAY-SUNDAY

Closed

 

FIND​ US

  • Twitter Square

Coopies Lane Industrial Estate

Morpeth

Northumberland

NE61 6JN

stanners@stanners-equipment.co.uk

Tel: 01670 514133
Fax: 01670 515492

Registered Office: Coopies Lane Ind. Est, Morpeth, Northumberland, NE61 6JN

Stanners Equipment Ltd. Company Reg. No: 1506945

Stanners Specialised Services LLP Company Reg. No: OC342971

Follow us on Twitter!